Altera Stratix V Avalon-MM Interface for PCIe Solutions User Manual Page 48
- Page / 184
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Signal Direction Description
IntxAck_o
Output This signal is the acknowledge for IntxReq_i. It is asserted for at
least one cycle either when either of the following events occur:
• The Assert_INTA message TLP has been transmitted in
response to the assertion of the IntxReq_i.
• The Deassert_INTA message TLP has been transmitted in
response to the deassertion of the IntxReq_i signal.
Refer to the timing diagrams below.
The following figure illustrates interrupt timing for the legacy interface. In this figure the assertion of
IntxReq_i instructs the Hard IP for PCI Express to send an Assert_INTA message TLP.
Figure 4-4: Legacy Interrupt Assertion
clk
IntxReq_i
IntAck_o
The following figure illustrates the timing for deassertion of legacy interrupts. The assertion of IntxReq_i
instructs the Hard IP for PCI Express to send a Deassert_INTA message.
Figure 4-5: Legacy Interrupt Deassertion
clk
IntxReq_i
IntAck_o
Physical Layer Interface Signals
Altera provides an integrated solution with the Transaction, Data Link and Physical Layers. The IP
Parameter Editor generates a SERDES variation file, <variation>_serdes.v or .vhd , in addition to the Hard
IP variation file, <variation>.v or .vhd. The SERDES entity is included in the library files for PCI Express.
Transceiver Reconfiguration
Dynamic reconfiguration compensates for variations due to process, voltage and temperature (PVT).
Among the analog settings that you can reconfigure are V
OD
, pre-emphasis, and equalization.
You can use the Altera Transceiver Reconfiguration Controller to dynamically reconfigure analog
settings. For more information about instantiating the Altera Transceiver Reconfiguration Controller IP
core refer to Hard IP Reconfiguration .
UG-01097_avmm
2014.12.15
Physical Layer Interface Signals
4-15
64- or 128-Bit Avalon-MM Interface to the Application Layer
Altera Corporation
Send Feedback
- User Guide 1
- Datasheet 2
- Features 3
- Interface 4
- Release Information 7
- Device Family Support 7
- Altera FPGA 8
- Debug Features 10
- IP Core Verification 10
- Recommended Speed Grades 11
- Running Qsys 14
- Generating the Example Design 15
- Simulating Altera Designs 17
- Time TLP Type Payload 18
- TLP Header 18
- Creating a Quartus II Project 19
- Compiling the Design 19
- Programming a Device 20
- Parameter Settings 21
- Parameter Value Description 22
- Device Capabilities 25
- Error Reporting 26
- Link Capabilities 27
- MSI and MSI-X Capabilities 28
- Power Management 29
- Clock Domains on page 6-5 33
- Application Layer 34
- RX Avalon-MM Master Signals 36
- Clock Signals 41
- Signal Direction Description 42
- Variant Logical Interfaces 49
- Hard IP Status Extension 50
- Field and Bit Map 58
- 0134678951 58
- Bit(s) Field Description 59
- Serial Data Signals 60
- PIPE Interface Signals 64
- Test Signals 69
- Registers 70
- Altera-Defined VSEC Registers 78
- CvP Registers 79
- Address Range Register 83
- Bit Name Access Description 84
- Bits Name Access Description 85
- PCI Express Mailbox Registers 86
- Avalon-MM Mailbox Registers 90
- Address Name Access 91
- Description 91
- Byte Offset 91
- Register Dir Description 91
- Sending a Write TLP 97
- Root Port TLP Data Registers 99
- UG-01097_avmm 100
- 2014.12.15 100
- Related Information 101
- Bits Register Description 102
- Reset and Clocks 105
- Hard IP for PCI Express 106
- Example Design 106
- Clock Domains 109
- Data Rate Frequency 110
- Clock Summary 112
- Interrupts for Endpoints 113
- MSI/MSI‑X Support 115
- MsiIntfc_o[81:0] 116
- MsiControl_o[15:0] 116
- MsixIntfc_o[15:0] 116
- IntxReq_i 116
- IntxAck_o 116
- Error Handling 117
- Physical Layer Errors 118
- Data Link Layer Errors 118
- Transaction Layer Errors 119
- Error Type Description 120
- Status Bit Conditions 123
- IP Core Architecture 125
- Hard IP for PCI Express 126
- Top-Level Interfaces 127
- Avalon-MM Interface 127
- Clocks and Reset 127
- Transceiver Reconfiguration 127
- Interrupts 127
- Data Link Layer 128
- Altera Corporation 129
- Send Feedback 129
- Physical Layer 130
- TX Packets 131
- Avalon‑MM Bridge TLPs 135
- Byte Enable Value Description 136
- PCI Express Avalon-MM Bridge 138
- RX Block 144
- Avalon-MM RX Master Block 144
- TX Block 145
- Interrupt Handler Block 145
- Enable PLL calibration 147
- Throughput Optimization 151
- Throughput of Posted Writes 153
- Design Implementation 155
- CONF_DONE 156
- Endpoint Reset 156
- Root Port Reset 156
- SDC Timing Constraints 157
- Optional Features 159
- ECRC on the RX Path 160
- ECRC on the TX Path 161
- Debugging 163
- Setting Up Simulation 166
- Use Third-Party PCIe Analyzer 168
- BIOS Enumeration Issues 168
- Address[31:2] 169
- Figure A-6: I/O Read Request 171
- 7 6 5 4 3 2 1 0 175
- Core Config 8 4 1 175
- Additional Information 177
- Date Version Changes Made 178
- How to Contact Altera 182
- Typographic Conventions 182
- Visual Cue Meaning 183
Related products and manuals for Measuring instruments Altera Stratix V Avalon-MM Interface for PCIe Solutions
(175 pages)© 2020, manymanuals.com. All rights reserved. | 0.373 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals